ENFORCER RF RECEivERs ENFORCER RF RECEivERs
Fixed-Code: 68 billion codes. CODEBUMP
code-hopping: 18 quintillion (1.8 x 10
19
) codes
Compatible Transmitters
SECO-LARM
®
U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Tel: 800-662-0800 / 949-261-2999 Fax: 949-261-7326
Website: www.seco-larm.com
E-mail: sales
@
seco-larm.com
Specifications:
The SECO-LARM policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right to change specications without further notice.
WARRANTY: These ENFORCER RF receivers are warranted against defects in material and workmanship while used in normal
service for a period of one (1) year from the date of sale to the original customer. Our obligation is limited to the repair or replacement of
any defective part if the unit is returned, transportation pre-paid, to SECO-LARM.
15 transmitter button codes per channel
CODEBUMP
With SECO-LARM’s
CODEBUMP, so-called
code-grabbers and scan-
ners are rendered obsolete
because the RF code changes
every time the transmitter
button is pressed. In addition,
with over 18 quintillion (1.8
x 10
19
) codes, the chances
of ever repeating a code are
virtually non-existent.
SECO-LARM’s CODEBUMP
transmitters and receivers
are perfect for controlling
garage and gate openers,
car and home alarms,
plus much more.
FILE: D\DTP\Manual\Mi-SK-910RAxxQ_051013.indd
Order Part #762-107-3%
Note: Products with model numbers that end with “Q” or that have a round green”Q”sticker are RoHS compliant.
l
Up to 500 ft. range
l
Operate on 11-24VAC/DC
1
l
Code learning
l
FCC compliant
l
Fixed code or CODEBUMP code-hopping
Copyright © 2013 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in part,
without the written permission of SECO-LARM.
Page 4
Model Number
SK-919TD1S-U
SK-919TD1S-UP
SK-919TD2A-U
SK-919TD2A-UP
SK-917T2A
SK-919TP3J-N
SK-917T3J
SK-919TP4J-N
SK-917TP4J-N
Model Number
SK-919TP1H-B
SK-919TP2H-N
SK-919TP4H-N
SK-9HBC
Pendant Remotes
Hand-Held Remotes
Accessories
1
2
3
4
# of
Buttons
# of
Buttons
1
2
4
1
3
15
# of
Channels
Coding
Fixed
Fixed
Fixed
Blank or
Pre-coded
Pre-coded
Pre-coded
Pre-coded
Blank or
Pre-coded
Blank
Pre-coded
Blank
Pre-coded
Pre-coded
Pre-coded
Pre-coded
Pre-coded
Pre-coded
Fixed
Fixed
Fixed
Fixed
Code Hopping
Fixed
Code Hopping
Fixed
Code Hopping
# of
Channels
1
3
7
15
Belt clip holster for hand-held remotes
Coding
®
PITSW1
Models Available
SK-910RAQ ............1-channel mini-receiver, 3A Form “C” relay, 315MHz
SK-910RAVQ .........1-channel mini-receiver, 5A transistor ground output, 315MHz
SK-910RAV2Q .......2-channel mini-receiver, 3A transistor ground outputs, 315MHz
SK-910RA-4Q ........1-channel mini-receiver, 3A Form “C” relay, 433.92MHz
SK-910RAV-4Q ......1-channel mini-receiver, 5A transistor ground output, 433.92MHz
SK-910RAV2-4Q ...2-channel mini-receiver, 3A transistor ground outputs, 433.92MHz
More RF receivers are available (1 to 4 channels). Contact SECO-LARM for details.
SK-910RAQ SERIES
Miniature RF
Receivers
Installation Manual
ENFORCER
®
1
All models work on 11-24VAC/DC, except for the low voltage versions.
SECO-LARM
®
Range
Operating Voltage
Memory Capacity
Current Draw
Output mode
Output type
Dimensions
Frequency
Transmitter
Up to 500’ range
5mA standby, 50mA LED ashing @
12VDC
Up to 500’ range
3-13.8 VDC
5mA standby, 15mA LED ashing @ 12VDC
Programmable 4-sec. momentary (default), 1-sec. momentary, toggle (ON/OFF), or validity
3A Form ‘C’ relay (NO/NC/C).
Transistor GND x 1, 5A @ 12VDC Transistor GND x 2, 3A @ 12VDC
3
3
/
16
” x 2
9
/
16
” x
3
/
4
” (80 x 65 x 19 mm)
315MHz. (Other frequencies available. Please contact SECO-LARM.)
Compatible with all SECO-LARM transmitters
SK-910RAQ
SK-910RAVQ
SK-910RAV2Q
11-24 V AC/DC (16~24 VAC/DC must cut LP4)
SK-910RAQ
Shown
Introduction
These mini RF receivers are compatible with both code hopping and xed-code transmitters (see page 4 of this manual
for a list of compatible transmitters). They can be used for a variety of applications, such as allowing the same transmitter to
arm/disarm a vehicle alarm and open/close a garage door opener. The receivers come in one- or two-channel versions.
Each channel can learn the codes of up to 15 different transmitter buttons on a rst-in, rst-out basis.
Installation Notes
1. Mount out of sight in a location where it is not surrounded by metal, and where it is not exposed to the weather or
moisture. Metal will block the RF signal, resulting in a reduced range.
2. For best range, pull the antenna wire as straight and high as possible. If the receiver receives interference from local
RF activity (eg., airport or military base), the antenna wire can be folded. DO NOT CUT THE ANTENNA WIRE.
(4 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals